 Tel:86-0731-88908466 Email:administrator@borunmould.com
Home > Industry Information > The type and use of brass rod
Online Service
Tony

Mr. Tony

Leave a message
Contact Now

The type and use of brass rod

2018-05-22
  There are various kinds of brass bars, such as H59, H62, H63, H65, H68, H70, H75, H80, H85, H90, H96, etc. Different products need different brass rods.Then, it is necessary to know the purpose of each brass rod.   1. H59 brass bar.   Can do all kinds of deep drawing and bending machine parts, such as pin, rivet, washer, nut, pipe, pressure gauge, screen mesh, radiator parts, etc.It has excellent machine function, excellent plastic in hot state, plastic in cold state, good cutting ability, easy welding and welding, corrosion resistance, it is a common type of ordinary brass.   The strength, hardness and plasticity are poor, but under the heat treatment, the pressure processing can be well received, the corrosion resistance is normal, and other functions are adjacent to H62.Used for ordinary mechanical parts, welding parts, hot stamping and hot stamping parts.   2. H62 brass rod.   It has excellent mechanical function, good plasticity under hot state, plastic in cold state, good cutting property, easy soldering and welding, corrosion resistance, but easy to inoculate and rupture.The other price is cheap, and is an ordinary brass of the habitual criminal.Used for all kinds of reciprocating parts, such as pin, rivet, washer, nut, tube, spring, screen, radiator parts etc.   3. H63 brass bar.   It is practical in cold - state pressure processing, suitable for stop welding and brazing.It is easy to polish, it is the main alloy that stops drawing, forming and bending.Used for screws, pickling rolls, etc.   4. H65 brass bar.   The function is between H68 and H62. The price is cheaper than H68, and also has higher strength and plasticity. It can accept cold and hot pressure processing well, and has a tendency of corruption and rupture.Used for hardware, daily necessities, small springs, Bolts, rivets and machine parts.   5. H68 brass bar.   There are excellent plasticity (the best in brass) and high strength, good machining function, easy to weld, not stable to common corruption, but easy to breed and crack.It is the most common type of common brass.Used for large cold stamping parts and deep punching parts, such as radiator shell, pipe, bellows, shell, gasket, etc.   6. H70 brass rod.   There are excellent plasticity (the best in brass) and high strength, good machining function, easy to weld, not stable to common corruption, but easy to breed and crack.Used for large cold stamping parts and deep punching parts, such as radiator housing, ducts, bellows, shell and gaskets.   7. H75 brass rod.   Good mechanical function, process function and corrosion resistance.Can work well in hot and cold conditions.It is between H80 and H70 in function and economy.Used for low load corrosion resistance springs.   8. H80 brass bar.   The function is similar to H85, but the strength is higher and the plasticity is better. It has high corrosion resistance in atmosphere, seawater and seawater.Used for making paper, thin wall tube, bellows and building supplies.   9. H85 brass bar.   It has high strength and good plasticity. It can accept cold, hot pressure, welding and corrosion resistance.For condensing and heat dissipation pipe, siphon, serpentine tube, cooling setup equipment decoration.   10. H90 brass rod.   The function is similar to H96, but the strength is slightly higher than H96, which can be used to compress the enamel.Used for water supply and drainage pipes, MEDALS, works of art, water tank and bimetallic strip.   11. H96 brass bar.   Good thermal conductivity, electrical conductivity, in the atmosphere and yet have high corrosion resistance, and has excellent plasticity, easy to machining, cold and hot pressure easy to welding, casting, and tin plating, no stress decay break bias.It is used as a conduit, condensing tube, radiator tube, radiator fin, automobile water tank and conductive part in ordinary machine.   NITONI, As a China Precision Mold Parts, Core Pin, Ejector Pin, Mold punch, Mold parts, Mold Components, Non-standard Precision Parts , Plastic mold parts , press die mold parts, manufactur and supplier,At present, The mould accessories products are mainly divided into Non-standard mold parts, Plastic mould parts, Press die mold parts, Die Springs, welcome to understand the customization.

Changsha Borun Mould Co. Ltd.
Business Type:Manufacturer
Product Range:Moulds
Products/Service:Hot runner nozzle , Ejector Sleeve , Die Springs Series , Non-standard Precision Parts , Standard Components for Plastic Mold , Hot runner components
Certificate:ISO9001
Company Address:Room 203 , 102 & 103, A8 Building, Jinrongtongxin international industrial park, Huizhi Rd., Leifeng town, Lu-Valley High-tech district, Changsha, Hunan, China

Previous: Kielce Poland plastics processing PLASTPOL exhibition in 2018

Related Products List

Home

Product

Whatsapp

About Us

Inquiry